CPC-Cplink - Revision history

Polluks: /* Key Features */

2021-05-11T13:25:03Z

‎Key Features

Polluks: Category

2021-05-11T13:23:11Z

Polluks: /* Gallery */ template

2021-05-11T13:19:49Z

‎Gallery: template

Revaldinho: Add more photos

2019-11-10T17:23:54Z

Add more photos

Revaldinho at 17:18, 10 November 2019

2019-11-10T17:18:54Z

Revaldinho: Created page with "= CPC-CPLINK = A co-processor link card for Amstrad CPC Computers (Pronounced CPC-Ker-Plink - as in the game of old) == Summary == This is a card which allows you to conn..."

2019-11-10T17:14:52Z

Created page with "= CPC-CPLINK = A co-processor link card for Amstrad CPC Computers (Pronounced CPC-Ker-Plink - as in the game of old) == Summary == This is a card which allows you to conn..."

New page

= CPC-CPLINK =

A co-processor link card for Amstrad CPC Computers

(Pronounced CPC-Ker-Plink - as in the game of old)

== Summary ==

This is a card which allows you to connect an external co-processor, like a RaspberryPi, directly to any Amstrad CPC Computer.

The card provides an easy to use parallel interface between the processors using First-In First-Out (FIFO) hardware and a simple message passing software protocol. Voltage level shifting components are included so that both 3V3 and 5V co-processors can be connected directly. Most likely the co-processor will be a RaspberryPi, but the interface is suitable for other processors and systems including Arduinos, Teensy and PIC MCUs.

FIFO based operation ensures all key timing requirements are handled by the board, so that any co-processor can be easily interfaced without needing to run bare-metal, timing critical code. e.g. A Raspberry Pi running a full Rasbian (Linux) distribution and a relatively low performance language like Python is perfectly suitable. This kind of co-processor could make some of its own OS resources available to the CPC, for example an SD card interface, timers, serial links etc.

The board has a convenient connector to allow a RaspberryPi Zero to be plugged directly into the back of the card and powered from the FIFO card itself. Other Pis will fit (although access to the HDMI port is awkward at the bottom of the card), but can more easily be connected using a short 50W ribbon cable. Many other CPUs including Arduino, Teensy, ChipKit, PIC MPUs can be connected with a suitable cable adapter. The board is compatible with both 3V3 and 5V signalling (3V3 coprocessors need to supply a 3V3 reference voltage to the card via a dedicated pin on the connector).

== Key Features ==

Here is a list of the key features:

* suitable for all CPC models
** uses a 50W box connector for compatibility with popular expansion boards
* compatible with external processors using either 5V or 3.3V IO signalling
* RaspberryPi compatible socket on rear
** plug in a Pi Zero and power directly from the FIFO card
** other (larger) Pi models or other CPUs incl. Arduino, Teensy can connect with a cable adapter
* Simple access protocol
** Byte wide, 16 byte deep FIFO in both directions with status flags
** separate status register and data register mapped into CPC IO port space
** byte wide data bus and flags/control signals driven by coprocessor GPIO
* Documentation and support files provided
** programming and construction notes
** examples of CPC and RaspberryPi code for simple loopback testing
*** Python and C coprocessor examples for Raspberry Pi
*** BASIC, BCPL/assembler and C examples for Amstrad CPC
*** Assember coded libraries are provided for both BCPL and C
** Loopback examples demonstrate data rates of
*** ~50KBytes/s with the CPC checking FIFO flags byte by byte
*** >100KBytes/s using block transfers (coprocessor checking for overrun only)
*** Higher rates are possible with more loop unrolling/burst transfer protocols
* Simple construction using cheap and easily available parts
** all through-hole, dual in line package, 74 Series logic design
** no programmable CPlD,FPGA,GAL,MPU or other parts
* Fully open source project licensed under the GNU GPL3
** includes all PCB layout (Eagle and gerber) and logical netlist files

== Status ==

The project has been fully built and tested.

For more detailed information, refer to the [https://github.com/revaldinho/cpc-cplink/wiki project wiki pages].

== License ==

All programs and data files in this project are made available under the terms of the GNU General Public License v3.

← Older revision		Revision as of 13:23, 11 May 2021
Line 67:		Line 67:

	</gallery>		</gallery>
		+
		+
		+	[[Category:DIY]]

@@ Line 59: / Line 59: @@
 == Gallery ==
-[[File:V1.0_assembled_front.jpg|thumbnail]]
+<gallery caption="PCB">
-[[File:ExpBoardCPCLINK_rear.jpg|thumbnail]]
-[[File:HeaderDetail.jpg|thumbnail]]
+Image:V1.0_assembled_front.jpg
-[[File:BCPL_test_scnshot.jpg|thumbnail]]
+Image:ExpBoardCPCLINK_rear.jpg

← Older revision		Revision as of 17:23, 10 November 2019
Line 59:		Line 59:
	== Gallery ==		== Gallery ==

		+	[[File:V1.0_assembled_front.jpg\|thumbnail]]
	[[File:ExpBoardCPCLINK_rear.jpg\|thumbnail]]		[[File:ExpBoardCPCLINK_rear.jpg\|thumbnail]]
		+	[[File:HeaderDetail.jpg\|thumbnail]]
		+	[[File:BCPL_test_scnshot.jpg\|thumbnail]]

@@ Line 35: / Line 35: @@
 ** examples of CPC and RaspberryPi code for simple loopback testing
 *** Python and C coprocessor examples for Raspberry Pi
-*** BASIC, BCPL/assembler and C examples for Amstrad CPC
+*** BASIC, [[BCPL]]/assembler and C examples for Amstrad CPC
 *** Assember coded libraries are provided for both BCPL and C
 ** Loopback examples demonstrate data rates of

@@ Line 4: / Line 4: @@
 (Pronounced CPC-Ker-Plink - as in the game of old)
 == Summary ==
@@ Line 54: / Line 56: @@
 All programs and data files in this project are made available under the terms of the GNU General Public License v3.