View source for FutureOS Header

Like in [[AMSDOS]] in [[FutureOS]] it's possible to store files in two ways: headerless and with a file-header. Headerless files are often files which need to fit into an 16 KB block, but don't need to be located in a specific RAM block. Applications and Executables normally have a file header. The file-header for FutureOS is strongly expanded compared to Amsdos, but fully compatible. It consists of 128 bytes and contain the following data:

 Byte(s) ! meaning, function
 --------!----------------------------
      00 ! Usernumber of file &00..&FE, &E5 for deleted entry. Don't use &FF!
 01 - 08 ! Filename (8 bytes) (fill unused char with spaces)
 09 - 0B ! Extent (3 bytes) (fill unused char with spaces)
 0C - 11 ! I00 to I05 (6 bytes) icon-data
      12 ! Filetype: &00 = basic, &02 = binary, &0A = Prowort
         ! Protected files: add &01, example: &01 = protected basic
         ! FutureOS files: add &80, 8. bit is set
      13 ! Horizontal range or X-width for semi-graphic-icon
      14 ! Vertical range or Y-lines for semi-graphic-icon
 15 - 16 ! Low, High-byte start/load-address of file LSB first
      17 ! Physical RAM-block of start/load address: &C0, &C4, &C5-&FF
 18 - 19 ! Low, High-byte file-length LSB first (first 16 bit)
 1A - 1B ! Low, High-byte execution / auto-start-address LSB first, else &0000 if not used
      1C ! Over-byte of file-length ==> file-length up to 16 MB
      1D ! Physical RAM-block of auto-start-address: &C0,&C4,&C5-&FF
 1E - 3F ! I06 to I27 (34 bytes) icon-data
 40 - 41 ! Repeat of L, H-byte file-length, but NOT USED!
      42 ! Icon-type: text-, graphic- or semi-graphic icon
 43 - 44 ! Low, High-byte checksum of this file-header LSB first
 45 - 7F ! I28 to I62 (59 bytes) icon-data

* Such a header contains &63 = 99 byte icon-data. 
* The icon-type-byte (&42) decides which kind of icon the file-header contains. This can be a graphic icon with 4 * 3 or 6 * 2 chars, a semi-graphic-icon or a text-icon. 
* There are four different icon-types. All icons are made for MODE 1 (32 characters, 32 lines usually).
* If the icon is a text-icon (icon-type is &00), the text can give information about the contents of the file or whatever. 
* A semi-graphic-icon (type &02) contains text in its icon-data too. These chars are displayed as an ASCII-rectangle. The header-bytes &13 and &14 contain the rectangles X and Y range. But X * Y must be < &64. Text and semi-graphic icons can contain all 256 characters. All control codes are displayed as characters. The difference is that the text of a text-icon is displayed as one string, whereas a semigraphic icon is a rectangle made out of characters.
* The true graphic icons contain only screen mode 1 graphic-data. They can have the format of 2 * 3 (type &01) or 3 * 2 (type &03) characters. 
* Therefore a graphic-icon uses only 4 * 3 * 8 = 96 bytes from the 99. The remaining three bytes can be used freely.

To calculate the checksum just add all bytes from 00 up to and including byte 66 together. The checksum is then placed to bytes 67 and 68, LSB first.

This is only a summary. All details are in the FutureOS manual, page 41-42.

[[Category:Disc Operating System]]
[[Category:FutureOS]]
[[Category:Programming]]